PDA

View Full Version : 78 parts bike


jilles
03-30-2007, 06:55 AM
I have too many extra parts I have one complete bike in boxes if anyone needs I have a couple extra complete front ends two motors completely taken apart in boxes. complete set of front and rear calipers and mastercyl. that work just took it off the bike yesterday

BIG MIC
04-05-2007, 03:39 PM
am looking for turn signal switch







Rubber down and the throttle back!!!!

jilles
04-10-2007, 05:33 AM
Just got back to work this morning and got your post if you are still interested . I will check tonight and post back to you thanks

jilles
04-12-2007, 08:13 AM
I checked on the turnsignals not in the greatest shape sorry

tonio116
04-15-2007, 08:40 PM
do you have the line for the front brake. This cable is connected to the brake light and it is installed at one end of the brake lever. Again it is the cable that turns the brake light on. thanks

jilles
04-16-2007, 05:46 AM
Sorry there wasn't one on the bike when I recieved it

xschop
05-02-2007, 08:09 AM
I need a rear caliper piston...in good shape

jilles
05-02-2007, 08:51 AM
Was trying to sell the complete rear end assy

Wirkinman
05-04-2007, 08:41 PM
I'm in need of the retainers that goes over the fork ears and holds the headlight secure. Their rectangular and has a reflector that faces outward.

Thank you,

Jes

jilles
05-07-2007, 05:55 AM
This one had some sort of aftermarket chome light sorry

ScottsXS
05-12-2007, 05:35 PM
what about side covers for 78e and seat hold downs??

jilles
05-14-2007, 05:39 AM
These are in too bad of shape to reuse sorry

Cyrock
05-16-2007, 05:11 PM
I need a Case, Chain Tensioner. I was re-tensioning the chain when the bolt stripped.

Ken Talbot
05-16-2007, 05:42 PM
Originally posted by Cyrock
I need a Case, Chain Tensioner. I was re-tensioning the chain when the bolt stripped.

Cyrock, that is an easy heli-coil fix. Use the search button at the top of the page and look for 'helicoil' and 'tensioner'

Be very careful about turning over the motor only by hand until you get the tensioner fixed. If you try to start it up, and the chain is worn, there is a high risk of the chain jumping a tooth, and this will cause bent valves. You want to avoid this! :eek:

Cyrock
05-16-2007, 07:08 PM
Thanks Ken - I've not turned the engine over since I set the timing mark. I guess my next question is where I could find a helicoil kit?

Ken Talbot
05-16-2007, 09:22 PM
Any industrial or automotive supply shop should be able to set you up. On this side of the border, we've got places like Acklands, CenturyVallen, NAPA, Lordco. McMasterCarr supply would probably have these available online too.

jilles
05-17-2007, 05:08 AM
If you send me a pic of what you need I have 2 engines totally disasembeled in boxes maybe I can help with a housing and or covers

Cyrock
05-21-2007, 07:49 AM
After looking at the housing, I found that the previous owner had put a 6mm heli-coil in the housing and that is what stripped out. Saturday I went out looking for a 7 mm heli-coil and was unable to find one. It seems everyone had a 8 mm but no one had a 7 mm. The 8 mm looked to be too big so I did the next best thing. I put a 1/4 heli-coil and that worked.

brew
05-22-2007, 05:58 PM
do you have a kick starter available?

dmakk777
05-29-2007, 08:27 PM
I need crome speedo and tach, also need a tear drop gas tank for my 79 xs1100sf

mbazzle
06-10-2007, 08:33 AM
I'm looking for the air cleaners that attach to the back of the carbs. I just bought a 1978 XS Eleven and it doesn't have that part. I'm also in need of the right side cover. Do you have these? Thanks! Looking forward to riding!!!!!

Dsxs11
06-10-2007, 09:32 AM
Needed the headlight. Maybe the gauges.