Forum: XS11/XJ11 Discussion
09-03-2012, 06:20 PM
|
Replies: 24
Views: 2,316
|
Forum: Members Lounge
09-03-2012, 05:15 PM
|
Replies: 17
Views: 2,586
|
Forum: Members Lounge
09-03-2012, 04:35 PM
|
Replies: 12
Views: 1,588
I've been a type II diabetic and on oral...
I've been a type II diabetic and on oral medication for over 5 years now and just recently I was able to reach the milestone of reaching the point of being diet controlled and getting OFF the...
|
Forum: Members Lounge
09-03-2012, 03:56 PM
|
Replies: 14
Views: 2,785
That was one of two colors for the 80G's. The...
That was one of two colors for the 80G's. The specials were far more popular in 80, and even more so in 81. But yes, the specials got the slotted rotors and the standards didn't, the H was the only...
|
Forum: Members Lounge
09-03-2012, 01:37 PM
|
Replies: 10
Views: 2,145
It was made by Vetter for Yamaha, I actually...
It was made by Vetter for Yamaha, I actually talked to Craig Vetter about it and he put me in touch with the engineer who did the modifications to the Windjammer IV to take the square turn signals...
|
Forum: XS11/XJ11 Discussion
07-25-2012, 05:26 PM
|
Replies: 28
Views: 3,498
|
Forum: XS11/XJ11 Discussion
07-25-2012, 05:15 PM
|
Replies: 53
Views: 6,940
If the rubber plug is needed and is missing it...
If the rubber plug is needed and is missing it will hardly run at all off idle, as it will bog as the main circuit will get fed unrestricted fuel without going through a jet as with no plug that...
|
Forum: XS11/XJ11 Discussion
07-25-2012, 05:07 PM
|
Replies: 53
Views: 6,940
|
Forum: XS11/XJ11 Discussion
07-25-2012, 04:49 PM
|
Replies: 10
Views: 11,737
I know they are not super common either, but 80...
I know they are not super common either, but 80 or 81 standard side covers can be made to fit, you only need to modify the top mounting holes, the side covers are shaped exactly the same, with the...
|
Forum: XS11/XJ11 Discussion
07-25-2012, 04:40 PM
|
Replies: 49
Views: 12,024
The problem with ethanol is that it's very...
The problem with ethanol is that it's very corrosive and damages the fuel system components of older vehicles that are not designed for it. It also attracts water and will cause the inside of the...
|
Forum: Members Lounge
07-25-2012, 01:55 PM
|
Replies: 18
Views: 3,839
|
Forum: XS11/XJ11 Discussion
07-20-2012, 09:07 PM
|
Replies: 29
Views: 8,060
|
Forum: XS11/XJ11 Discussion
07-12-2012, 10:36 PM
|
Replies: 19
Views: 2,253
Yes, but the end of the wire can be corroded...
Yes, but the end of the wire can be corroded after 30 years, and cutting 1/4 inch or so off will usually get you back to nice clean copper and give you good contact and fix the problem. Many of us...
|
Forum: XS11/XJ11 Discussion
07-12-2012, 10:17 PM
|
Replies: 3
Views: 1,043
Wouldn't have expected the TCI to cause...
Wouldn't have expected the TCI to cause intermittent stuff like that, it would usually be hard fail, but what you describe sounds a LOT like the pickup coil type problem which is pretty much always...
|
Forum: XS11/XJ11 Discussion
07-12-2012, 10:13 PM
|
Replies: 30
Views: 9,364
The bungee is supposed to attach to the pieces...
The bungee is supposed to attach to the pieces that you want to cut off, all the way at the end of them, and should run under the carbs to hold those in together. There should be a small hole in...
|
Forum: XS11/XJ11 Discussion
07-12-2012, 10:08 PM
|
Replies: 20
Views: 2,533
|
Forum: XS11/XJ11 Discussion
07-12-2012, 08:17 PM
|
Replies: 30
Views: 3,448
|
Forum: XS11/XJ11 Discussion
07-11-2012, 09:11 PM
|
Replies: 9
Views: 1,322
If you have a broken mixture screw in the carb...
If you have a broken mixture screw in the carb you're not going to get the idle to work right, or get it to take off from a stop right either until to fix that. I don't remember where they are, but...
|
Forum: XS11/XJ11 Discussion
07-11-2012, 09:05 PM
|
Replies: 10
Views: 1,646
80 and 81 standards in stock shape have the...
80 and 81 standards in stock shape have the hazard switch as well, it's common to the 80 and later bikes, the control pods are the same for special and standard at least as far as the controls go.
|
Forum: XS11/XJ11 Discussion
07-11-2012, 08:41 PM
|
Replies: 40
Views: 5,560
I don't know, I thought the 80 and 81's were...
I don't know, I thought the 80 and 81's were jetted the same, but only having an 80 I could be wrong. I've got an 81 engine in mine, but the carbs are 80 carbs with everything else being from 80.
|
Forum: XS11/XJ11 Discussion
07-11-2012, 08:33 PM
|
Replies: 31
Views: 2,857
IF I go with HID I will go with one of the DOT...
IF I go with HID I will go with one of the DOT approved HID kits, but they are unfortunately only made for round headlights, which means for the specials for those of use with the TRUE Vetter (not...
|
Forum: XS11/XJ11 Discussion
07-11-2012, 08:26 PM
|
Replies: 30
Views: 9,364
|
Forum: XS11/XJ11 Discussion
07-11-2012, 08:22 PM
|
Replies: 30
Views: 9,364
I think you will find they will rattle and flap...
I think you will find they will rattle and flap without those pieces, as those pieces are clearly not about anything else, but are part of the bracing for the lowers to tie the back of them together...
|
Forum: XS11/XJ11 Discussion
07-10-2012, 11:55 PM
|
Replies: 31
Views: 5,415
|
Forum: XS11/XJ11 Discussion
07-09-2012, 09:52 PM
|
Replies: 8
Views: 1,347
|