Forum: XS11/XJ11 Discussion
03-29-2016, 12:23 PM
|
Replies: 18
Views: 3,460
|
Forum: XS11/XJ11 Discussion
03-24-2016, 08:08 PM
|
Replies: 36
Views: 9,102
|
Forum: XS11/XJ11 Discussion
03-23-2016, 07:25 PM
|
Replies: 36
Views: 9,102
Video.......
Video.... http://www.xs11.com/forum/showthread.php?t=35349
|
Forum: XS11/XJ11 Discussion
02-27-2016, 01:26 PM
|
Replies: 13
Views: 3,063
|
Forum: XS11/XJ11 Discussion
02-22-2016, 12:22 PM
|
Replies: 4
Views: 907
|
Forum: XS11/XJ11 Discussion
02-22-2016, 11:49 AM
|
Replies: 13
Views: 3,063
Here's what you need......
Here's what you need... http://www.xs11.com/forum/showthread.php?t=36551
Maybe somebody here has a hacked frame that could cut the mounts off of for you...
|
Forum: XS11/XJ11 Discussion
02-21-2016, 03:18 PM
|
Replies: 16
Views: 2,423
It all gets down to your comfort level after...
It all gets down to your comfort level after inspecting the tires. Personally, where I live I wouldn't hesitate to run those tires if they looked good. You hear lots of antidotal horror stories, but...
|
Forum: XS11/XJ11 Discussion
02-21-2016, 02:28 PM
|
Replies: 6
Views: 1,468
|
Forum: XS11/XJ11 Discussion
02-20-2016, 03:59 PM
|
Replies: 16
Views: 2,423
|
Forum: XS11/XJ11 Discussion
02-19-2016, 02:01 PM
|
Replies: 22
Views: 3,335
|
Forum: XS11/XJ11 Discussion
02-18-2016, 08:07 PM
|
Replies: 7
Views: 1,596
|
Forum: XS11/XJ11 Discussion
02-16-2016, 02:21 PM
|
Replies: 8
Views: 1,533
$200 for a solid complete XS exhaust is a good...
$200 for a solid complete XS exhaust is a good deal... But do make sure it's complete. Parts for many of the aftermarket exhausts are getting every bit as rare as good OEM systems. For some bits, if...
|
Forum: XS11/XJ11 Discussion
02-12-2016, 02:05 PM
|
Replies: 15
Views: 2,805
To check the reed switch, connect a OHM meter...
To check the reed switch, connect a OHM meter across the two wires coming off it, then turn the speedometer. The switch should open/close/open as you turn...
You may need an analog meter as most...
|
Forum: XS11/XJ11 Discussion
02-10-2016, 03:01 PM
|
Replies: 60
Views: 5,999
I made one for the rear caliper on my XJ...
I made one for the rear caliper on my XJ project.... http://www.xs11.com/forum/showthread.php?t=37206
The main thing to remember is these are there to prevent the pad thrust surfaces from wearing...
|
Forum: XS11/XJ11 Discussion
02-09-2016, 02:15 PM
|
Replies: 7
Views: 1,282
Like Phil said, they're supposed to cancel on a...
Like Phil said, they're supposed to cancel on a time/distance basis. Stopped at a light, they generally will stay on until you move but not always. You might check to see if the reed switch in the...
|
Forum: XS11/XJ11 Discussion
02-08-2016, 03:06 PM
|
Replies: 29
Views: 3,199
|
Forum: XS11/XJ11 Discussion
02-04-2016, 11:40 AM
|
Replies: 115
Views: 13,404
|
Forum: XS11/XJ11 Discussion
02-03-2016, 02:06 PM
|
Replies: 3
Views: 1,101
|
Forum: XS11/XJ11 Discussion
02-01-2016, 01:45 PM
|
Replies: 14
Views: 2,094
Mike, read this:...
Mike, read this: http://www.xs11.com/forum/showthread.php?t=35339 for directions on how to read the meter and what to look for. One problem is the meter doesn't put any load on the connections so...
|
Forum: XS11/XJ11 Discussion
02-01-2016, 12:50 PM
|
Replies: 14
Views: 2,094
If everything except the ignition/start circuit...
If everything except the ignition/start circuit work, that's where the problem lies. Start at the fuse panel, make sure you have 12V power to ground on both sides of the ignition fuse with the fuse...
|
Forum: XS11/XJ11 Discussion
01-31-2016, 02:25 PM
|
Replies: 56
Views: 13,669
|
Forum: XS11/XJ11 Discussion
01-31-2016, 01:06 PM
|
Replies: 5
Views: 2,050
If it were single wall pipe, you could use a...
If it were single wall pipe, you could use a fabricated mandrel to remove most of the dent, but with double wall you'll never get it all out. If you're determined to fix it, the best way would be to...
|
Forum: XS11/XJ11 Discussion
01-29-2016, 12:04 AM
|
Replies: 21
Views: 6,326
There may be two issues with 'printed' parts;...
There may be two issues with 'printed' parts; one, will the material hold up to brake fluid, sunlight, etc? Two, the degree of 'finish' due to printer 'resolution' that seems to be available with...
|
Forum: XS11/XJ11 Discussion
01-27-2016, 01:42 PM
|
Replies: 115
Views: 13,404
Cheap sync tool.......
Cheap sync tool.... http://www.xs11.com/forum/showthread.php?t=986
This is what I use, it works just fine. A bit slower to use, but no worries about if the multiple gauges are all calibrated the...
|
Forum: XS11/XJ11 Discussion
01-27-2016, 02:08 AM
|
Replies: 15
Views: 2,805
How The OEM Turn Signals Work
The XS turn signals are unlike any other turn signals circuits you've ever ran into. The flasher isn't really a flasher, it's a special relay and the canceller prevents the relay from closing under...
|