Home arrow Forums



Go Back   XS11.com Forums > Idle Talk Forum > Product Evaluations

Reply
 
Thread Tools Display Modes
  #1  
Old 03-15-2019, 10:56 PM
XSSIVEUS's Avatar
XSSIVEUS XSSIVEUS is offline
XSive
 
Join Date: Jul 2018
Location: Fairfield, CA USA
Posts: 35
Replacement Tank Trim

Hi folks,

On this and other XS sites I've read threads asking about what to use to replacement the original metal edge trim used on fuel tanks such as the XS1100E and XS1100LG Midnight Special models. After much research and trial & error I've found an acceptable, low cost replacement. Attached are pix of the replacement black tank molding on one of my XS1100s. This replacement trim is a U-shaped trim used as edge molding on car doors. It comes with an adhesive bead already applied in the bottom of the "U". You clean with tank edge with alcohol wipes that come with the trim, cut it to length, center it, and apply it. I found that this trim is slightly larger (5/16" high vs 1/4" high) than the original metal trim, but only by 1/16". One side of the trim is slightly shorter than the other, so this is the side I used facing outward to best replicate the original. I applied it on a XS1100E that has finished restoration and it looks great! It sticks well and should be a good alternative to a NOS replacement IF you can find one (I couldn't and I looked for months world-wide). I also bought metallic gold colored which will go on my XS1100LG MS that is being repainted now. Once you determined the correct length (from original trim or ad pix from Yamaha), cut it to length, marked the center line with a wedge of painters tape, and start applying it at the center of the tank trim just behind the triple fork. This resulted in an even application because once you shove it on, you'll have a hard time removing it. Here are pix of replacement and original black and gold trims:

Original black trim on 78 XS1100E:
https://xssive.smugmug.com/Tank-Trim...Tf/i-3qXcQDK/A

Replacement black trim:
https://xssive.smugmug.com/Tank-Trim...Tf/i-7nQTKLZ/A
https://xssive.smugmug.com/Tank-Trim...Tf/i-zrNfpcK/A
https://xssive.smugmug.com/Tank-Trim...Tf/i-Nw5P8Dd/A

Original gold trim on XS1100LG:
https://xssive.smugmug.com/Tank-Trim...Tf/i-X9sGj9c/A

Replacement gold trim:
https://xssive.smugmug.com/Tank-Trim...Tf/i-qXnXwVh/A

You can buy this in the US on eBay under the heading of "Edge Trim Car Truck SUV Door Edge Guards Gloss Black" and "Gold Car Door Edge Guard Trim". There are a variety of sellers, but these guys had decent prices and I didn't have to wait for questionable stuff from China (voice of experience here). 8' or more is enough length for (2) bikes, either color, and can be had for $10-$15. It appears to be fairly high quality, sticks like crazy, and solves the problem of how to trim your tank when the NOS isn't available any more. I'm satisfied and I'm picky.

If you have any questions, please PM me.

Glen
Modify message
__________________
78 XS1100E touring, original owner
78 XS1100E, restored stock
80 XS1100LG Midnight Special, restoration project
83 XJ750MK Midnight Special, restoration project
97 FLH, original owner
Reply With Quote
  #2  
Old 03-16-2019, 12:42 AM
dansmith65 dansmith65 is offline
Truly XSive
 
Join Date: Aug 2017
Location: Creston, B.C. , Canada
Posts: 103
Looks good! Thanks for sharing that.
__________________
80 SG Canada
Reply With Quote
  #3  
Old 03-23-2019, 10:57 AM
fredintoon's Avatar
fredintoon fredintoon is offline
Master of XSology
 
Join Date: Mar 2004
Location: Saskatoon SK
Posts: 6,788
Quote:
Originally Posted by XSSIVEUS View Post
Hi folks,

On this and other XS sites I've read threads asking about what to use to replacement the original metal edge trim used on fuel tanks such as the XS1100E and XS1100LG Midnight Special models. After much research and trial & error I've found an acceptable, low cost replacement. Attached are pix of the replacement black tank molding on one of my XS1100s. This replacement trim is a U-shaped trim used as edge molding on car doors. It comes with an adhesive bead already applied in the bottom of the "U". You clean with tank edge with alcohol wipes that come with the trim, cut it to length, center it, and apply it. I found that this trim is slightly larger (5/16" high vs 1/4" high) than the original metal trim, but only by 1/16". One side of the trim is slightly shorter than the other, so this is the side I used facing outward to best replicate the original. I applied it on a XS1100E that has finished restoration and it looks great! It sticks well and should be a good alternative to a NOS replacement IF you can find one (I couldn't and I looked for months world-wide). I also bought metallic gold colored which will go on my XS1100LG MS that is being repainted now. Once you determined the correct length (from original trim or ad pix from Yamaha), cut it to length, marked the center line with a wedge of painters tape, and start applying it at the center of the tank trim just behind the triple fork. This resulted in an even application because once you shove it on, you'll have a hard time removing it. Here are pix of replacement and original black and gold trims:

Original black trim on 78 XS1100E:
https://xssive.smugmug.com/Tank-Trim...Tf/i-3qXcQDK/A

Replacement black trim:
https://xssive.smugmug.com/Tank-Trim...Tf/i-7nQTKLZ/A
https://xssive.smugmug.com/Tank-Trim...Tf/i-zrNfpcK/A
https://xssive.smugmug.com/Tank-Trim...Tf/i-Nw5P8Dd/A

Original gold trim on XS1100LG:
https://xssive.smugmug.com/Tank-Trim...Tf/i-X9sGj9c/A

Replacement gold trim:
https://xssive.smugmug.com/Tank-Trim...Tf/i-qXnXwVh/A

You can buy this in the US on eBay under the heading of "Edge Trim Car Truck SUV Door Edge Guards Gloss Black" and "Gold Car Door Edge Guard Trim". There are a variety of sellers, but these guys had decent prices and I didn't have to wait for questionable stuff from China (voice of experience here). 8' or more is enough length for (2) bikes, either color, and can be had for $10-$15. It appears to be fairly high quality, sticks like crazy, and solves the problem of how to trim your tank when the NOS isn't available any more. I'm satisfied and I'm picky.

If you have any questions, please PM me.

Glen
Modify message
Hi Glen,
thanks for the information, I've been living with 3 naked edge bike tanks for decades that'd be enhanced by that strip. Plus a thin windshield that has it's existing edge trim broken in 2 places that such a strip will hopefully replace.
So long as the US supplier can cope with shipping to Canada that is. I'd swear that some of them don't know that there's anything North of the 49th parallel.
__________________
Fred Hill, S'toon
XS11SG with Spirit of America sidecar
"The Flying Pumpkin"
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 12:33 AM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Integrated by BBpixel ©2004-2019, jvbPlugin