Home arrow Forums



Go Back   XS11.com Forums > Idle Talk Forum > Members Lounge

Reply
 
Thread Tools Display Modes
  #1  
Old 07-19-2018, 07:58 PM
dave mcleod dave mcleod is offline
New
 
Join Date: May 2009
Location: vancouver
Posts: 3
looking for a member in vancouver, canada to help me work on my 1100 maxim

hi members,
a few months ago i wrote to the administration asking advice on getting my 1100 maxim running. it was working well 4 years ago when i had a low speed crash and cracked the stator housing. it wouldn't charge after that, although i managed to get it running long enough to limp home and park it. i had just replaced the cdi box and had a new clutch installed, so it seems a shame to junk it. a couple of days later i got a very helpful letter from T.C. Gresham, recommending that i seek out a member in my area to teach me how to fix it.

last week i got the stator cover welded and reinstalled it. if i'm lucky, the rotor may spin without shorting out. yesterday i talked with my old mechanic at the local yamaha dealership and got an estimate on what he would charge to clean/tune carbs, install new tires and valve shims and a battery. about $1500 canadian was the ballpark estimate. i don't mind the cost of the tires and installation so much as the 500 for the carb work alone.

i'd like to do the work myself if there was a knowlegable member in my city willing to help me out. someone with the instruments needed for carb sych. compensation can be discussed with the right person. thanks for your attention. dave mcleod
Reply With Quote
  #2  
Old 07-19-2018, 10:59 PM
sethhope's Avatar
sethhope sethhope is offline
Truly XSive
 
Join Date: May 2016
Location: Quakertown, pa
Posts: 185
Welcome to the forums!

I'm not in your area, but I'm sure the people here could help out! I would first check the maintenance and repair section for an overview on the carbs. The carbs are the heart and soul of these bikes. They're also pretty easy once you get a grasp of what's inside it.

As for the valve shims, doing the adjustment is also pretty straight forward. Just need a good feeler gauge and a few wrenches.

I recommend picking up a Clymer manual for the bike. I keep one with Roxy as a sort of 'bible' on fixing the XS11.

Good luck finding someone in your area! I'm sure there's someone on here nearby.
__________________
1979 XS1100F "Roxy" (my first bike ) - '91 Suzuki GSX1100 Fairing, BMW bags, Cheap ABS Trunk, aftermarket cruiser seat, MAC 4-2 exhaust, Heavy Duty folding kickstart, XS11 Special signals and gauges, Blade Fuse Conversion, Dynacoil Greens w/ ballast bypass, SS brake lines
Reply With Quote
  #3  
Old 07-19-2018, 11:58 PM
dave mcleod dave mcleod is offline
New
 
Join Date: May 2009
Location: vancouver
Posts: 3
thanks for your thoughts, seth. i'll read up what i can about the carbs - i do have the repair manual and owners manual for this bike. hopefully, someone in my neighbourhood will see this thread and look me up.
Reply With Quote
  #4  
Old 08-02-2018, 05:40 AM
mack mack is offline
XS-XJ Guru
 
Join Date: Sep 2009
Location: Ontario, Canada
Posts: 2,386
Carbs

These carbs are a hobby of mine. If your not comfortable doing them ship them to me with return post and I'll clean them up and send them back. If no parts are required your cost would be just shipping.
__________________
mack
79 XS 1100 SF Special
HERMES
original owner
http://i946.photobucket.com/albums/a...ps6932d5df.jpg

81 XS 1100 LH MNS
SPICA
http://i946.photobucket.com/albums/ad305/mack-055/2.jpg

78 XS 11E
IOTA
https://youtu.be/wB5Jfbp6SUc
https://youtu.be/RaI3WYHSuWA



Have recovery trailer and shop if you breakdown in my area.
Frankford, Ont, Canada
613-398-6186
Reply With Quote
  #5  
Old 08-10-2018, 02:38 AM
dave mcleod dave mcleod is offline
New
 
Join Date: May 2009
Location: vancouver
Posts: 3
thank you Mack!

blown away by your generous offer to help... i have gotten one carb apart and cleaned and plan to reassemble it before going on the the next one. the brass needle on the idle screw was ridged and deteriorating at the tip, so i used a fine diamond hone to sharpen it like a pencil. i noted the number of turns it was open before dismantling so i ought to be able to get it close to where it was. there was a lot of green crystalized buildup in the float chamber and on the floats. is that from old fuel reacting with the copper of the floats? i didn't find any o rings on this carb when taking it apart. do these ones not have them?
Reply With Quote
  #6  
Old 08-10-2018, 04:22 AM
BillyRok BillyRok is offline
XStremely XSive
 
Join Date: Aug 2011
Location: Shortsville, NY.
Posts: 375
Just a Hobby?

Quote:
These carbs are a hobby of mine.
Mack, here in the states we call what you have an obsession!

Dave, if you get tired of messing with those carbs, take Mack up on his offer...they'll be perfect when you get them back. But the more you fool with them, the more you'll understand about 'em...have fun!
__________________
Billy

1982 XJ1100, Ceramic Coated Headers, Raptor ACCT, Barnett Clutch Springs, Dremmel Fix, TC's Fuse Block, De-Linked S/S Brake Lines, 850 Final Drive, Yahman's YICS Eliminator, Pods, stock jets
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 11:02 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Integrated by BBpixel ©2004-2018, jvbPlugin